Uit Hack42
k (→Printed parts: ontbrekende lengtes) |
|||
| Regel 11: | Regel 11: | ||
! !! naam !! Kleur !! Aantal !! Filament used | ! !! naam !! Kleur !! Aantal !! Filament used | ||
|- | |- | ||
| − | | {{check}} || Bar clamps || groen || 1 || @m90 | + | | {{check}} || Bar clamps || groen || 1 || 7170@m90 |
|- | |- | ||
| {{check}} || Z screw pointer || geel || 2 || 142@prusa | | {{check}} || Z screw pointer || geel || 2 || 142@prusa | ||
| Regel 35: | Regel 35: | ||
| || wades extruder || groen || 1 || @m90 | | || wades extruder || groen || 1 || @m90 | ||
|- | |- | ||
| − | | {{check}} || wades large gear || paars || 1 || @m90 | + | | {{check}} || wades large gear || paars || 1 || 1519@m90 |
|- | |- | ||
| {{check}} || wades small gear || groen || 1 || 982@m90 | | {{check}} || wades small gear || groen || 1 || 982@m90 | ||
Versie van 19 jul 2012 12:49
| Project: Leluq90 | |
|---|---|
  Leluq90 | |
| Naam | Leluq90 |
| Door | BugBlue |
| Status | Uitvoer |
| Madskillz | knippen en plakken |
| Doel / Omschrijving | |
| Mendel90 in mooie kleurtjes | |
| Alle Projecten - Project Toevoegen | |
noez
Printed parts
| naam | Kleur | Aantal | Filament used | |
|---|---|---|---|---|
 |
Bar clamps | groen | 1 | 7170@m90 |
|
Z screw pointer | geel | 2 | 142@prusa |
|
Z Motorbrackets | groen | 1 | 4311@m90 |
|
Z limit switch | geel | 1 | 860@prusa |
|
Z coupling | geel | 4 | 1739 @prusa |
|
Y motor bracket | groen | 1 | 2591 @m90 |
|
Y idler bracket | geel | 1 | 1317 @prusa |
|
Y bearing mount | geel | 1 | 2882 @prusa |
| X motor bracket | oranje | 1 | 9044 @prusa | |
|
X idler bracket | oranje | 1 | 4652 @prusa |
|
X carriage | geel | 1 | 5358 @m90 |
| wades extruder | groen | 1 | @m90 | |
|
wades large gear | paars | 1 | 1519@m90 |
|
wades small gear | groen | 1 | 982@m90 |
|
ribbon clamps | geel | 1 | 1005 @prusa |
|
pulley | geel | 2 | 746 @prusa |
|
fixing blocks | geel | 10 | 8707 @prusa |
| Totaal | - | 31 |
Te bestellen onderdelen
Electronica, motors, lagers, mechanica, etc. (eigenlijk alles behalve schroeven e.d.). Triviale dingen weggelaten (bijv. alu-tape, ventilator, voeding, etc.).
| Onderdeel | Prijs | Stuks | Prijs / st. | Bron | Status |
|---|---|---|---|---|---|
| Sanguinololu (incl. motor drivers) | €85 | 1 | €85 | RRW | |
| NEMA17 x 47.5mm stappermotor | €62,50 | 5 | €12,50 | RRW | |
| J-Head MK IV-B | €50 | 1 | €50 | xyz | |
| Verwarming printoppervlak 214×214mm | €26 | 1 | €26 | eBay (incl. thermistor) | |
| Hobbed bolt | €10 | 1 | €10 | xyz | |
| Lagers 608ZZ | €1 | 3 | €0,30 | RRW | |
| Lagers 624ZZ | €1 | 3 | €0,30 | RRW | |
| Lineaire lagers LM8UU | €10 | 10 | set, €10 | RRW:eBay | |
| Tandriemen T5, 6mm | €7 | 1 (set) | €7 | RRW | |
| 9 pins D-plug | 1 | ? | |||
| 9 pins D-socket | 1 | ? | |||
| Glasplaat 214mm × 202mm × 2mm | <€3,5 | 1 | ? | ||
| Eindstopschakelaars | ~€7,20 | 3 | ~€2,40 | RRW |
|
| Slang 7mm (buiten) × 5mm (binnen) × 16mm | 2 | space | |||
| Veer 12mm (buiten) × 0.75mm (draad) × 10mm | 1 | space | |||
| Veer 7mm (buiten) × 1mm (draad) × 10mm | 2 | ballpoint | |||
| Rubber ring M3 × 10mm × 1.5mm | 2 | eerst maar eens zonder | x | ||
| Kabels, kabels, kabels | space | ||||
| Totaal | ~€275 |