Uit Hack42
| Regel 18: | Regel 18: | ||
* Rewire | * Rewire | ||
: Since it is a makerbot cupcake CNC with a seperate extruderboard and a steppermotordriver connected to the extruderboard rewirering was needed since the extruder steppermotor is now connected directly to the mainboard. The extruderboard is now the only switching and controlling the temperature of the heated bed and the extruded | : Since it is a makerbot cupcake CNC with a seperate extruderboard and a steppermotordriver connected to the extruderboard rewirering was needed since the extruder steppermotor is now connected directly to the mainboard. The extruderboard is now the only switching and controlling the temperature of the heated bed and the extruded | ||
| − | |||
: New cables and connectors for the hotend are needed | : New cables and connectors for the hotend are needed | ||
* Printbed | * Printbed | ||
: The original printbed of the makerbot is very unstable this has to change | : The original printbed of the makerbot is very unstable this has to change | ||
| − | : TODO: New printbed with glassplate and isolation | + | : TODO: <s>New printbed with</s> glassplate <s>and isolation</s> |
* Z threaded rods | * Z threaded rods | ||
: they are bend in very ugly shapes. These need to be replaced | : they are bend in very ugly shapes. These need to be replaced | ||
* Calibration | * Calibration | ||
: X Y and Z calibration are very easy. Extruded calibration should be done at the right temperature. | : X Y and Z calibration are very easy. Extruded calibration should be done at the right temperature. | ||
| − | : TODO: extruder recalibration | + | : TODO: extruder recalibration (again) |
* Retraction | * Retraction | ||
: Since it takes a *lot* of steps (gearbox) to retract retraction time is slow, retraction is set to only 0.2mm during print | : Since it takes a *lot* of steps (gearbox) to retract retraction time is slow, retraction is set to only 0.2mm during print | ||
| − | : TODO: lower this value | + | : TODO: lower this value - get rid of makergear. |
* Endstops | * Endstops | ||
: There are no endstops | : There are no endstops | ||
: TODO: install 6 endstops, drill holes to install them and wire them. (easy). | : TODO: install 6 endstops, drill holes to install them and wire them. (easy). | ||
* Grease | * Grease | ||
| − | : TODO: Apply more. | + | : <s>TODO: Apply more.</s> |
== Conclusion == | == Conclusion == | ||
It was a nice desing at some time, however newer firmware and a lot of improvements can make it a very nice and fast printer. | It was a nice desing at some time, however newer firmware and a lot of improvements can make it a very nice and fast printer. | ||
Versie van 28 jul 2012 01:24
| Project: Makerbot | |
|---|---|
  Makerbot | |
| Naam | Makerbot |
| Door | BugBlue |
| Status | Uitvoer |
| Madskillz | Solderen, firmware fixen, schroeven, boren, meten |
| Doel / Omschrijving | |
| Makerbot een revisie geven zodat die normaal werkt | |
| Alle Projecten - Project Toevoegen | |
noez
|
Beklemmingsgevaar
|
Introduction
Got a makerbot from revspace. Where one of it's members had it sitting on a desk for about a year without any good quality prints I decided to rob them and fix it completely with an overhaul
The fixes
- J-Head 0.35 printhead
- The new J-Head extruded behaves much more nicely, doesn't jam up and gives a very nice output
- Teacup firmware
- New teacup firmware makes it possible to use pronterface and slic3r as software. Giving much nicer control, monitoring and easier settings than any of the other old software.
- Rewire
- Since it is a makerbot cupcake CNC with a seperate extruderboard and a steppermotordriver connected to the extruderboard rewirering was needed since the extruder steppermotor is now connected directly to the mainboard. The extruderboard is now the only switching and controlling the temperature of the heated bed and the extruded
- New cables and connectors for the hotend are needed
- Printbed
- The original printbed of the makerbot is very unstable this has to change
- TODO:
New printbed withglassplateand isolation
- Z threaded rods
- they are bend in very ugly shapes. These need to be replaced
- Calibration
- X Y and Z calibration are very easy. Extruded calibration should be done at the right temperature.
- TODO: extruder recalibration (again)
- Retraction
- Since it takes a *lot* of steps (gearbox) to retract retraction time is slow, retraction is set to only 0.2mm during print
- TODO: lower this value - get rid of makergear.
- Endstops
- There are no endstops
- TODO: install 6 endstops, drill holes to install them and wire them. (easy).
- Grease
TODO: Apply more.
Conclusion
It was a nice desing at some time, however newer firmware and a lot of improvements can make it a very nice and fast printer.